| |||||
AFCA Forums > Antique Fan Collectors Association > Buy-Sell-Trade > WTB-Emerson oscillator shoulder screw |
Moderated by: Steve Cunningham, Rod Rogers, Larry Hancock |
|
WTB-Emerson oscillator shoulder screw | Rating: ![]() |
Author | Post |
---|
Posted: Fri Aug 16th, 2013 11:42 am |
|
1st Post |
Brian Kurtt AFCA Member ![]()
![]() |
Anyone have one they can part with? Attached Image (viewed 921 times): Last edited on Fri Aug 16th, 2013 11:43 am by Brian Kurtt |
|||||||
|
Posted: Fri Aug 16th, 2013 03:48 pm |
|
2nd Post |
Carl Parker AFCA Member
![]() |
McMaster-Carr sells them for a few dollars each
|
|||||||
|
Posted: Fri Aug 16th, 2013 07:15 pm |
|
3rd Post |
Brian Kurtt AFCA Member ![]()
![]() |
LOL!! you're kidding? Those folks have everything - I should've checked them first - Thank you
|
|||||||
|
Posted: Sat Aug 17th, 2013 02:07 pm |
|
4th Post |
Tom Newcity AFCA Member ![]()
![]() |
Carl Parker wrote: McMaster-Carr sells them for a few dollars each Carl, Would you please share that M/C part number? I've never been able to find it with the correct length. Thanks.
|
|||||||
|
Posted: Sat Aug 17th, 2013 02:33 pm |
|
5th Post |
Carl Parker AFCA Member
![]() |
may take till tomorrow Tom I need to dig through paperwork which my wife does better she's not here. I've ordered probably 3-4 different Emerson shoulder screws from them. They are not exact copies, like the heads may be thicker or wider but I've gotten several common sizes for I believe all the emersons and some for the 50's Hunter Zephairs. I'll post the numbers asap
|
|||||||
|
Posted: Thu Aug 22nd, 2013 12:16 am |
|
6th Post |
Dan Proctor AFCA Member
![]() |
Brian - Did you get the shoulder screw you needed? I needed one for an 8" Emerson Jr and placed an order last night through Amazon for a 5 pack of the closest match I could find: Slotted 303 SS, Shoulder Diameter 3/16", Shoulder Length 1/8", Head Diameter 5/16", Thread Length 3/16", Thread Size 8-32. The only dimension out of spec for me was the head height... which is 5/32". Let me know if you need one... it's the least I could do as thanks for the FF videos of Paul and Tom!
|
|||||||
|
Posted: Thu Aug 22nd, 2013 12:20 am |
|
7th Post |
Brian Kurtt AFCA Member ![]()
![]() |
Well, that's very kind - I'd be happy to pay for one or two and the shipping - I'll PM the address and please consider letting me pay for it. Thank you
|
|||||||
|
Posted: Thu Aug 22nd, 2013 12:51 am |
|
8th Post |
Dan Proctor AFCA Member
![]() |
They will be in the mail to you, hopefully Saturday... good karma! Thanks again for your efforts to record and post the videos! Last edited on Thu Aug 22nd, 2013 01:56 am by Dan Proctor |
|||||||
|
Posted: Thu Aug 22nd, 2013 03:32 am |
|
9th Post |
Tom Newcity AFCA Member ![]()
![]() |
Dan Proctor wrote: Brian - Did you get the shoulder screw you needed? I needed one for an 8" Emerson Jr and placed an order last night through Amazon for a 5 pack of the closest match I could find: Slotted 303 SS, Shoulder Diameter 3/16", Shoulder Length 1/8", Head Diameter 5/16", Thread Length 3/16", Thread Size 8-32. The only dimension out of spec for me was the head height... which is 5/32". Let me know if you need one... it's the least I could do as thanks for the FF videos of Paul and Tom! You are probably going to have to grind down the thread length. If it goes in too far, it will bind up the mechanism. I don't have any exact dimensions right now, but be aware of it.
|
|||||||
|
Posted: Thu Aug 22nd, 2013 10:39 am |
|
10th Post |
Chad Hunter AFCA Member
![]() |
Hey Carl were you able to dig up the McMaster-Carr part numbers if so please post. Thanks C
|
|||||||
|
Posted: Sat Aug 24th, 2013 01:07 am |
|
11th Post |
John Fengel AFCA Member ![]()
![]() |
Carl Parker wrote: may take till tomorrow Tom I need to dig through paperwork which my wife does better she's not here. I've ordered probably 3-4 different Emerson shoulder screws from them. They are not exact copies, like the heads may be thicker or wider but I've gotten several common sizes for I believe all the emersons and some for the 50's Hunter Zephairs. I'll post the numbers asap Carl, can you post the McMaster part numbers for the 3-4 Emerson Shoulder Screws. I'd sure like to order some. John
|
|||||||
|
Posted: Sat Aug 24th, 2013 06:39 am |
|
12th Post |
Russ Huber AFCA Member ![]()
![]() |
Would any of these examples work for Emerson? I am to tired, and have to go to bed. http://www.allmetricsmallparts.com/products/hardwarescrews.htm
|
|||||||
|
Posted: Sat Aug 24th, 2013 12:43 pm |
|
13th Post |
Rudy Benvin Guest ![]()
![]() |
I bought a shoulder bolt for the same fan from Mcmaster-Carr and found out that the thread length had to be ground down otherwise the thread would bottom out and bind but it worked after a little tweaking with the threads. McMaster # 99154A360
|
|||||||
|
Posted: Sun Aug 25th, 2013 03:06 am |
|
14th Post |
Dan Proctor AFCA Member
![]() |
That one would have been perfect for my Jr, except I needed 1/8" shoulder length... I was not able to find that with a low profile head, so I had to settle for one with the thicker head height. Brian - yours are on the way and your oscillator arm looks like it will work well with the shorter shoulder length. It worked perfectly on my Jr, but Jr doesn't have the adjustable oscillator wheel. Thread length is the same on both, so it sounds like you will have to do a little grinding.
|
|||||||
|
Posted: Sun Aug 25th, 2013 04:29 am |
|
15th Post |
Brian Kurtt AFCA Member ![]()
![]() |
No worries, I can make it work. Thank you!
|
|||||||
|
Posted: Tue Aug 27th, 2013 09:06 pm |
|
16th Post |
Brian Kurtt AFCA Member ![]()
![]() |
Dan, the screws just arrived and they work perfectly with the exception of the threaded portion being a tad too long. Would you send me the Amazon info where you purchased these? I'd like to get a small supply. Thank you!!!
|
|||||||
|
Posted: Tue Aug 27th, 2013 11:09 pm |
|
17th Post |
Dan Proctor AFCA Member
![]() |
Brian - Glad you were able to make it work. Here's the link: http://www.amazon.com/dp/B001P5VIA0/ref=biss_dp_t_asn Notice the link, "See all 45 in this Product Family", near the top if you're looking for different sizes.
|
|||||||
|
Posted: Tue Aug 27th, 2013 11:19 pm |
|
18th Post |
Ken Rodoni Guest ![]()
![]() |
Anyone know of a similar source for LH shoulder screws (GE, Hunter)?
|
|||||||
|
Current time is 10:50 am | |
AFCA Forums > Antique Fan Collectors Association > Buy-Sell-Trade > WTB-Emerson oscillator shoulder screw | Top |