AFCA Forums Home
Home Search search Menu menu Not logged in - Login | Register
AFCA Forums > Antique Fan Collectors Association > Pre-1950 (Antique) > Hunter Century C16 Oscillation Parts Advice

 Moderated by: Steve Cunningham, Rod Rogers, Larry Hancock
New Topic Reply Printer Friendly
Hunter Century C16 Oscillation Parts Advice  Rate Topic 
AuthorPost
 Posted: Thu Mar 14th, 2019 03:39 pm
  PMQuoteReply
1st Post
Pat Murphy
AFCA Member
 

Joined: Fri Nov 23rd, 2018
Location: Elk Creek, Virginia USA
Status: 
Offline

I'm not sure I have all the parts, or the correct parts, for this fan: A Hunter Century C16, pre-1950.

After disassembly I noticed that I may be missing a small hex nut. As seen on the On/Off control, there apparently should be some sort of hex nut or bolt head to fit inside there. The 1/8" 32 tpi screw is all that it had. Would anyone know what I should have, and what the correct dimensions should be? Are the threads reversed?

A little more info: The knob and screw do not actuate the oscillation gears. That is either because the knob just spins around the screw, or because the last 2-3 threads are worn down too much to turn the gear. I am guessing that a hex head type of screw, inserted into the knob, and the pair threaded onto the gear may be needed???

I didn't attach a photo of the oscillation gear connection point since it is masked over for painting at the present. I was hoping to have this puzzle solved before the final clear coat step.

Any ideas would be appreciated.
Thanks, Pat




Last edited on Thu Mar 14th, 2019 03:40 pm by Pat Murphy

Back To Top PMQuoteReply  

 Posted: Thu Mar 14th, 2019 08:03 pm
  PMQuoteReply
2nd Post
Levi Mevis
Guest


Joined: Tue Feb 24th, 2015
Location: Elkhart, Indiana USA
Status: 
Offline
I have a later version of your fan, I'll take a look at how the oscillator knob is done on my fan and get back to you.

Back To Top PMQuoteReply

 Posted: Fri Mar 15th, 2019 12:58 pm
  PMQuoteReply
3rd Post
Pat Murphy
AFCA Member
 

Joined: Fri Nov 23rd, 2018
Location: Elk Creek, Virginia USA
Status: 
Offline
Levi Mevis wrote: I have a later version of your fan, I'll take a look at how the oscillator knob is done on my fan and get back to you.Thank you much Levi

Back To Top PMQuoteReply  

 Posted: Fri Mar 15th, 2019 01:02 pm
  PMQuoteReply
4th Post
Levi Mevis
Guest


Joined: Tue Feb 24th, 2015
Location: Elkhart, Indiana USA
Status: 
Offline
I took a look at mine and it appears that mine just has a screw in it holding the oscillator engagement knob into place like what yours did. there may have not been a nut down there to begin with.

Back To Top PMQuoteReply

 Posted: Fri Mar 15th, 2019 01:51 pm
  PMQuoteReply
5th Post
Pat Murphy
AFCA Member
 

Joined: Fri Nov 23rd, 2018
Location: Elk Creek, Virginia USA
Status: 
Offline
Thank you sir!

Best I can tell the threads are reverse, yours?

That may explain my worn threads, and lack of proper engagement with my oscillator gear???

Back To Top PMQuoteReply  

 Posted: Fri Mar 15th, 2019 02:05 pm
  PMQuoteReply
6th Post
Levi Mevis
Guest


Joined: Tue Feb 24th, 2015
Location: Elkhart, Indiana USA
Status: 
Offline
I believe that's the way mine is as well, reverse threaded. It could be that the screw is not tightened down tight enough, I know that's been the case with some of my fans.

Back To Top PMQuoteReply

 Posted: Fri Mar 15th, 2019 04:23 pm
  PMQuoteReply
7th Post
Joel Schmid
AFCA Member
 

Joined: Sun Sep 9th, 2018
Location:  
Status: 
Offline
Hey Pat,
If you have a tap and die set you may be able to chase the threads on that screw and clean them up.
How much extra length does it have ? If it has a few threads to spare in length you can cut the stripped end off and de-burr it, then run it into the oscillator drive shaft and it should tighten up for you.

Back To Top PMQuoteReply  

 Posted: Fri Mar 15th, 2019 06:55 pm
  PMQuoteReply
8th Post
Pat Murphy
AFCA Member
 

Joined: Fri Nov 23rd, 2018
Location: Elk Creek, Virginia USA
Status: 
Offline
Thank for the idea Joel. I actually have a thread chaser tool I bought in an antique store.
It goes from 1/16th inch to 1/4 inch in 1/32nd steps, but there is no tpi specs listed :-(

I thought I would give it a try just in case it spins around as smoothly as it should. It is a real nifty tool!

Thanks,
Pat

Back To Top PMQuoteReply

Current time is 09:27 am  
AFCA Forums > Antique Fan Collectors Association > Pre-1950 (Antique) > Hunter Century C16 Oscillation Parts Advice Top



Beige Theme By: Di @ UltraBB
UltraBB 1.17 Copyright © 2007-2008 Data 1 Systems
Page processed in 0.1566 seconds (15% database + 85% PHP). 28 queries executed.