AFCA Forums Home
Home Search search Menu menu Not logged in - Login | Register

 Moderated by: Steve Cunningham, Rod Rogers, Larry Hancock
New Topic Reply Printer Friendly
Westinghouse Housing 164848  Rate Topic 
AuthorPost
 Posted: Sun Jun 9th, 2019 02:50 am
  PMQuoteReply
1st Post
Joe Sweitzer
Guest
 

Joined: Sat Jun 8th, 2019
Location: Maryland USA
Status: 
Offline
This is my first vintage fan. I am trying to split the motor housing so I can remove the stator to replace the headwire that is broken right inside the housing. However I can not get the front half of the housing to some off

Back To Top PMQuoteReply  

 Posted: Sun Jun 9th, 2019 03:28 am
  PMQuoteReply
2nd Post
Don Tener
AFCA Member


Joined: Fri Dec 21st, 2012
Location: Saint Petersburg FL, Florida USA
Status: 
Offline
I am assuming that this is a stamped steel model but a pic would help. Anyway get a real sharp chisel or knife. Slowly tap the chisel or knife into the seam of the housing with a hammer going from side to side. It will slowly start to separate. when you get a big enough opening for a screwdriver to fit then start working it with that until it comes apart.

Back To Top PMQuoteReply

 Posted: Sun Jun 9th, 2019 04:20 am
  PMQuoteReply
3rd Post
Dave McManaman
AFCA Member


Joined: Sat Apr 22nd, 2017
Location: Lincoln, Nebraska USA
Status: 
Offline
I've got one of these that i previously tore down and cleaned up but it's at my office.  If i remember right, there's a small gap in the seam at the bottom of the motor housing where you can get the blade of a small screwdriver in between and start opening it - then like Don said go around the perimeter and it'll open up.  I'm sure someone else will chime in if that's not the case.  Otherwise, I'll try to remember to take a look on Monday. 

Back To Top PMQuoteReply  

 Posted: Sun Jun 9th, 2019 01:29 pm
  PMQuoteReply
4th Post
Joe Sweitzer
Guest
 

Joined: Sat Jun 8th, 2019
Location: Maryland USA
Status: 
Offline
Here is a picture of the motor that I am trying to split apart. 

Attached Image (viewed 107 times):

20190609_092521.jpg

Last edited on Sun Jun 9th, 2019 01:34 pm by Joe Sweitzer

Back To Top PMQuoteReply

 Posted: Sun Jun 9th, 2019 02:07 pm
  PMQuoteReply
5th Post
Don Tener
AFCA Member


Joined: Fri Dec 21st, 2012
Location: Saint Petersburg FL, Florida USA
Status: 
Offline
Joe Sweitzer wrote: Here is a picture of the motor that I am trying to split apart. Yea that is what I thought. It is stamped steel. Just do like I posted above. I personally prefer using a chisel. It is easier to control while tapping with a hammer. It just needs to be good and sharp.

Back To Top PMQuoteReply  

 Posted: Sun Jun 9th, 2019 05:26 pm
  PMQuoteReply
6th Post
Joe Sweitzer
Guest
 

Joined: Sat Jun 8th, 2019
Location: Maryland USA
Status: 
Offline
Thanks for the help getting the front of the motor cover off. Can you please tell me the best way to get the stator out to get to the wires

Back To Top PMQuoteReply

 Posted: Wed Jun 12th, 2019 04:21 am
  PMQuoteReply
7th Post
David A Cherry
AFCA Member
 

Joined: Sun May 12th, 2019
Location: USA
Status: 
Offline
 once the front of the motor is off ...pull out the shaft..and at that point put both hands down on each side of the stater at this point have someone else placed a wooden dowel about an inch in diameter between your hands and as you lift up off the ground and holding it ... The second person will lightly tap the Dow with the hammer until you start to see movement if you don't see movement, start tapping a little harder,  if it's a stamped sheet metal motor you can whack it pretty good but if it's castiron you may want to go easy especially if it's a GE.  their castings are thin and not very strong...this has work for me 90% of the time... it does require two people thou!, thank God I have an understanding wife that likes to hammer into hundred year old motors housings while she's in the middle of one of her shows...

Back To Top PMQuoteReply  

Current time is 07:45 pm  
AFCA Forums > Antique Fan Collectors Association > Pre-1950 (Antique) > Westinghouse Housing 164848 Top



Beige Theme By: Di @ UltraBB
UltraBB 1.17 Copyright © 2007-2008 Data 1 Systems
Page processed in 0.1878 seconds (29% database + 71% PHP). 30 queries executed.