AFCA Forums Home
Home Search search Menu menu Not logged in - Login | Register

 Moderated by: Steve Cunningham, Stan Adams, Rod Rogers
New Topic Reply Printer Friendly
Rewiring a Westinghouse 321347  Rate Topic 
AuthorPost
 Posted: Thu Jul 25th, 2019 07:46 pm
  PMQuoteReply
1st Post
Ed Guy
Guest
 

Joined: Thu Jul 25th, 2019
Location:  
Status: 
Offline
My grandmother's Westinghouse 321347 is in pretty good mechanical condition, but the wiring is toast. I have managed to disassemble almost everything, including the 4 studs that project through the motor housing but can't figure out how to open the housing to connect new wire. Do Any magic, or do I just pull? Thanks and have a great day! 

Attached Image (viewed 411 times):

15640731339011049667872223228494.jpg

Back To Top PMQuoteReply  

 Posted: Thu Jul 25th, 2019 09:33 pm
  PMQuoteReply
2nd Post
Michael Heffernan
AFCA Member
 

Joined: Mon Oct 12th, 2009
Location:  
Status: 
Offline
To open the motor, place the edge of a box cutter blade at that groove in the case. tap it in and move it around. Then you should be able to put a small screw driver blade in there to finish the opening. Now, this will open the front, but these motors are wired from the rear and the front will give you no access to the head wire. For that you need to remove the core and that is another ball of wax.

Back To Top PMQuoteReply

 Posted: Thu Jul 25th, 2019 09:43 pm
  PMQuoteReply
3rd Post
David Kilnapp
AFCA Member
 

Joined: Tue Apr 17th, 2018
Location: Pembroke, Massachusetts USA
Status: 
Offline
Michael is exactly correct in his advice. I have a very thin knife that I use for this purpose but you must be VERY careful or the knife blade will jump and you will mark up the case. So just tap the knife on the joint. One more piece of advice. Parts of this fan are pot metal like the oscillator casing and the front nose. There is no point in removing them and you will have an exceptionally difficult time getting the holes to line up again to re-assemble it. You will break those pieces if you try to pry them off. If I'm not mistaken those are Micarta blades which place the date in the early 1920's. You will find that fan runs a bit hot but that's normal. I don't recommend removing the stator. That is a hellish job. Reinserting the stator back in the case with the holes lined up is equally difficult. I can't tell from you picture if there are any wire remnants protruding from the case. If there are, simply solder to them using the heat shrinking solder joints. They work well and will give a good strong bond. Cover them with the black heat shrink sleeves and you will be good to go. I have removed one of the stators from these pressed steel cases and I will NEVER do another. I hope you don't need to do that to get at the head wires. Not a fun job at all!

Last edited on Thu Jul 25th, 2019 09:44 pm by David Kilnapp

Back To Top PMQuoteReply  

 Posted: Thu Jul 25th, 2019 09:48 pm
  PMQuoteReply
4th Post
David Kilnapp
AFCA Member
 

Joined: Tue Apr 17th, 2018
Location: Pembroke, Massachusetts USA
Status: 
Offline
Is this your fan? If yes, it was manufactured in 1923. I gave it to my father in law for his birthday. He was born that year!

Back To Top PMQuoteReply

 Posted: Thu Jul 25th, 2019 10:32 pm
  PMQuoteReply
5th Post
Ed Guy
Guest
 

Joined: Thu Jul 25th, 2019
Location:  
Status: 
Offline
David, thanks for the quidance. Unfortunately, there is not a shred of wiring on the stator that I can attach to. Zip, zilch, nada.

Back To Top PMQuoteReply  

 Posted: Thu Jul 25th, 2019 10:34 pm
  PMQuoteReply
6th Post
Ed Guy
Guest
 

Joined: Thu Jul 25th, 2019
Location:  
Status: 
Offline
The badging is a little different. The last patent date is 10-31-22.

Back To Top PMQuoteReply

 Posted: Thu Jul 25th, 2019 10:48 pm
  PMQuoteReply
7th Post
Ed Guy
Guest
 

Joined: Thu Jul 25th, 2019
Location:  
Status: 
Offline
Thanks, Michael. The knife blade worked like a charm! 

Last edited on Thu Jul 25th, 2019 10:49 pm by Ed Guy

Back To Top PMQuoteReply  

 Posted: Thu Jun 9th, 2022 08:23 pm
  PMQuoteReply
8th Post
Ed Guy
Guest
 

Joined: Thu Jul 25th, 2019
Location:  
Status: 
Offline
All, I have decided not to put any more effort into restoring this fan; too many other things that I want to do. I'm willing to part with it for the cost of shipping from Northern Virginia. Reach out if you're interested.
Ed

Back To Top PMQuoteReply

Current time is 07:38 pm  
AFCA Forums > Antique Fan Collectors Association > Pre-1950 (Antique) > Rewiring a Westinghouse 321347 Top



Beige Theme By: Di @ UltraBB
UltraBB 1.17 Copyright © 2007-2008 Data 1 Systems
Page processed in 0.1210 seconds (52% database + 48% PHP). 29 queries executed.